Operation
Installation
Emptying the Drain Tank
General Precautions:
WARNING:
• Do not tip the CoolCube 10 on its side. If the CoolCube 10 has been on its side, stand it upright and
wait at least 2 hours before starting up the air conditioner. Failure to have the CoolCube 10 upright
for at least 2 hours after the unit has been on its side will result in damage to the CoolCube 10
• If the power cord or plug is damaged, repair should only be performed by qualified electrical
personnel
• Do not connect/disconnect the power cord or attempt to operate buttons with wet hands. This could
result in electrical shock
CAUTION:
Following are some precautions to consider before choosing your
installation site. Please review carefully as improper installation may
result in personal injury or damage to the unit.
• Do not use the unit in areas where leakage of flammable gas may occur
• Do not use the unit in an atmosphere of excessively corrosive gas or vapor
• Do not use in areas where the temperature is outside the allowable operating range:
Below 65°F 50%RH and Above 95°F 60%RH
• Do not install the unit in sloping areas. The unit may move or topple over even if the casters are set
to the LOCKED position
• Install the unit in areas that can withstand the weight of the unit. The CoolCube 10 unit weighs
approximately 130 lbs. (when the drain tank is full of water)
• Allow 12 inches of unobstructed airflow for both the air inlets and outlets
• The AC outlet (115 VAC Single Phase, 60 Hz) needs to be rated at 15A or higher. Do not share
outlet with any other instrument or equipment
• Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present,
wipe off with a clean, dry cloth
• Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is
found, contact your CoolCube reseller for repair
• Confirm the attachment plug is lit when it is plugged into an appropriate outlet. If the plug is not lit,
press the reset button the side.
NOTE:
• Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign matter
• The CoolCube 10 model is equipped with an approved NEMA plug configuration (5-15P). The
appropriate outlet must be used for this plug type
During the COOL mode, condensate will accumulate in the drain tank. When the drain tank
becomes full, the “FULL TANK” LED will illuminate along with an “FL” error code in the ROOM
TEMP LED display. The unit will automatically shut off.
1. If you want to empty the drain tank, while the unit is in operation, press the POWER button to turn
the unit off.
2. Pull the drain tank from the bottom of the unit.
3. Empty the drain tank into a nearby sink or drain.
4. Replace the drain tank back into the bottom of the unit, making sure that it is properly in place.
5. Press the POWER button to restart the unit.
Remove Full Drain Tank
CoolCube 10 Unit
DRAIN PUMP KIT (Optional)
A drain pump kit (UCP) is available to allow continuous operation and eliminate the need for a
drain tank.
• When the water collects to level (A) in the pump reservoir, the drain pump begins to operate and
discharge the water.
• When the water level drops below level (B), the drain pump stops.
NOTE:
If the pump’s discharge line is pinched/blocked or if the pump is not operating properly, the water
level will rise to level (C) and the pump will turn off the unit. The “FULL TANK” LED will
illuminate and “FL” will display in the ROOM TEMP display.
(C)
A
(B)
Drain Pump
15
Remove Drain Tank
Install Drain Pump
4
CoolCube 10 Unit
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales