MaxPower Corporation CoolCube 10 Especificaciones descargar pdf (Pagina 23)

omniPAGE mini wide

multiple minigel casting

■ Offers the capacity of two mini gels on a single gel

■ Rapid gel casting and loading

■ Optional low or high buffer volumes

■ Rapid set up cooling

The omniPAGE mini wide vertical gel unit with a gel width of 20cm effectively allows double the number of

samples to be resolved as the omniPAGE mini unit. This allows consistency of sample comparison on a

single gel and is designed for those with greater than 20 samples to compare and resolve.

Simple set up using ultra soft silicone seals guarantees trouble free glass plate loading and gel casting.

Dual gaskets on the gel running insert along with notched and plain glass plates ensure leak proof gel

running. Rapid set up cooling retains resolution in extended separations and also saves on buffer volume

without affecting run quality.

4mm thick glass plates reduce breakage and have bonded spacers for added convenience. A wide range

of accessories is available allowing many techniques to be performed using the same unit. Prep combs

can be used to maximise sample loading and recovery. Accessory electroblotting and tube gel modules are

available which use the same outer tank and lid.

Mini SDS PAGE, Native

PAGE, Gradient, Second

dimension and Nucleic

acid separations

Typical Applications

LATE DIMENSIONS

, 20

EL DIMENSIONS

, 18

NIT DIMENSIONS

SAMPLE

192

SAMPLES

CAPACITY

SAMPLES PER GEL

UFFER VOLUME

600

; M

2800

OMBS AVAILABLE

OF SAMPLES

1, 5, 10, 18MC, 24, 30, 36MC, 48

HICKNESSES

0.75, 1, 1.5, 2

Technical Specifications

VS10WD omniPAGE Mini Wide, 20 x 10cm Dual, 2 sets of Glass Plates with 1mm thick bonded Spacers, 2 x 24 sample, 1mm thick combs, cooling pack

VS10WDSYS omniPAGE Mini Wide, 20 x 10cm Dual, 2 sets of Glass Plates with 1mm thick bonded Spacers, 2 x 24 sample, 1mm thick combs, cooling pack including caster

VS10WDSYS-CU omniPAGE Mini Wide, 20 x 10cm Dual, 2 sets of Glass Plates, 1mm thick bonded Spacers, 2 x 24 sample, 1mm thick combs including caster, External casting upstand

Ordering Information

VS10WEXCASTER VS10W External Casting Stand - No Casting Base

VS20CAST 20 x 10cm Casting Base

VS20DCASTM Replacement Silicone Mat for 20 x 10cm Casting Base

VS10WDIRM Inner Running Module

VS20-x -LG Loading guides for omniPAGE mini combs, x = comb well number

VS10WNG 20 x 10cm Notched Glass Plates 4mm thick (pk/2)

VS10WPG 20 x 10cm Plain Glass Plates 4mm thick (pk/2)

VS10WNGS0.75 20 x 10cm Notched Glass Plates with 0.75mm Bonded Spacers (pk/2)

VS10WPGSO.75 20 x 10cm Plain Glass Plates with 0.75mm Bonded Spacers (pk/2)

VS10WNGS1 20 x 10cm Notched Glass Plates with 1mm Bonded Spacers (pk/2)

VS10WPGS1 20 x 10cm Plain Glass Plates with 1mm Bonded Spacers (pk/2)

VS10WPGS1.5 20 x 10cm Plain Glass Plates with 1.5mm Bonded Spacers (pk/2)

VS10WPGS2 20 x 10cm Plain Glass Plates with 2mm Bonded Spacers (pk/2)

VS10WDP Dummy Plate, 20 x 10cm

RPW-0.2 Replacement Platinum Wire - 0.2mm, 50cm

VS20ICB Maxi Cooling Pack

uses same combs as

VS20 systems

CSL-6CAST 6 gel caster for 8 x 10cm or 10 x 10cm gels

CSL-12CAST 12 gel caster for 8 x 10cm or 10 x 10cm gels

CSL-24CAST 24 gel caster for 8 x 10cm or 10 x 10cm gels

CSL-GM15 15ml Gradient Mixer

CSL-GM25 25ml Gradient Mixer

CSL-GM50 50ml Gradient Mixer

CSL-GM100 100ml Gradient Mixer

CSL-GM500 500ml Gradient Mixer

Ordering Information

■ Integral levelling feet and level bubble

■ Standard and gradient gels can be poured

■ Choice of 6, 12 or 24 gel casting models

Advance casting of multiple mini gels can help to achieve consistent

results between runs. These multiple gel casting systems are tailored

for use with omniPAGE mini vertical electrophoresis units; with three

models of 6, 12 and 24 gel capacities. Fewer gels can be poured if

required using the acrylic saver blocks supplied with each system.

The fixed hinged clamps allows the gel sandwich to be adjusted to the

correct pressure irrespective of the number or the thickness of gels

being poured. Separation sheets allow the easy separation of the glass

plates after pouring.

For combs,

see page 24

Ideal for Caesium, Sucrose and Gel gradients

these Gradient Mixers comprise two

chambers – a reservoir and a mixing

chamber with an

interconnecting

valve. A second

valve regulates the

output flow from the

mixing chamber. All

mixers have a flat

base which allows them to be placed on a

magnetic stirrer. A magnetic stirring bar

can be placed directly in the mixing

chamber to ensure a constant gradient.

The support rod allows the mixer to be

fixed to a retort stand for extra stability.

gradient mixers

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comentarios a estos manuales

Sin comentarios

MaxPower Corporation CoolCube 10 Especificaciones Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Acondicionadores de aire del sistema de división MaxPower Corporation CoolCube 10